Boehmer Heating & Cooling Blog: Posts Tagged ‘Furnace Repair’

Pittsburgh Heating Question: What To Do If Your Furnace Keeps Turning On or Off?

Monday, September 24th, 2012

Your Pittsburgh furnaces is designed to last decades without major problems so long as it is regularly maintained.  They typically work so well, in fact, there is a danger of taking our comfort for granted and skipping the annual service for a year or two as time rushes by, waking up suddenly and brutally to a dark night and no heat.

In retrospect, a preliminary indication of trouble could have been the furnace continually turning off and on in short bursts, something that was tugging at your senses, but not strongly enough to really catch your attention.

Possible Problems

A furnace constantly turning on and off could often be a direct result of poor airflow through the system.  Heat builds up and the detectors sense the proper temperatures have been reached and automatically shut down.  In the room, the thermostat calls for more heat and starts the cycle over again.

A relay switch or control valve may also be worn and working improperly.  A crack in the heat exchanger might fuel the flame to burn too hotly and cause the sensor to misinterpret the information and shut down.

These problems not only impede the distribution of heat to the living spaces, decreasing comfort, but also create intense wear on the motor and controls, threatening the very life of the appliance.

Simple Solutions

Restricted airflow can be caused most often by a dirty or clogged filter.  At the furnace, there is usually a panel that can be removed to check, clean or replace the filter.  It is typically a single or series of cardboard and screen panels approximately 1′ by 2′, but varies by manufacturer and furnace output.

A vacuum to pull lint free or compressor to blow it clean are the recommended tools to use a few times each year.  It is a good idea to change the filters at the beginning of each heating season. The belts are also easily replaced.

The fan belts for the blower may also be worn loose and not pushing the air hard enough to get through the filters.  It is a good idea to check them regularly as well.

The Calvary Charge

When in doubt, call the experts out.  Scheduling an annual inspection and service with Boehmer Heating & Cooling Company takes the worry out of living in a furnace heated home.  Call us today to schedule your appointment!

 

 

Continue Reading

Pittsburgh Heating Quesiton: What Are Flue Gas Spill Switches?

Wednesday, March 21st, 2012

While some components of their Pittsburgh heating system make sense to the average homeowner – think blower fan, thermostat and air ducts – others are more esoteric and prone to bouts of head scratching.

So, you may find yourself asking “what the heck is a flue gas spill switch?”

As you know, gas heating appliances produce heat by means of combustion. The gas line feeds gas into the appliance, the gas is ignited, and the burning gas produces heat. It’s a simple concept that goes all the way back to our caveman ancestors building fires to keep warm, and it is the same process in gas furnaces, boilers and water heaters.

In addition to producing the cozy heat we love in the winter time, this combustion process also releases gases. Known collectively as “flue gases,” some of these – carbon monoxide being the most notorious – can be very toxic. This why we have flues or chimneys in our homes– to give these gases a means of egress.

A flue gas spill switch is designed to shut down the furnace if these gases start seeping out. It is made up of a sensor or series of sensors that detect heat outside the flue, not unlike the flame sensor in your furnace. If flue gases start to escape and pass by the sensor, the sensor heats up and signals the furnace to shut down. This cuts off the power and gas, so that no more flue gases can leak into the home and create a health concern.

If your Pittsburgh furnace has been abruptly shutting down, it could be your flue gas spill switch trying to tell you that you have a leaky or cracked flue. If this is the case, you want to have it repaired right away. The constant off and on is not good for the furnace, and more importantly, those flue gases can be exceptionally hazardous to your family’s health.

Continue Reading

Bridgeville Heating Repair Tip: Furnace Control Boards

Friday, February 17th, 2012

One way to be a truly responsible Bridgeville homeowner is to familiarize yourself with the major systems and appliances in your home. By having at least some understanding of how, say, your refrigerator or toilet work, you gain understanding of how to use them efficiently and detect when something goes wrong.

The same is true of your furnace, which can appear to be a complicated piece of machinery. In order to help you get acquainted with your furnace, we will discuss one of its main control components, the furnace control board.

As the name suggests, furnace control boards are responsible for governing the operation of the furnace. At a minimum, a simple furnace control will control the furnace ignitor (e.g., a spark generator or glow coil), the gas valve and the furnace thermocouple, also called a flame sensor.

More complex furnace control boards will also have control over the blowers and/or the built-in diagnostic system.

To simplify things, you can think of the furnace control board as being a driver and the furnace as its car. Just as the driver oversees all the functions and operation of the car from ignition to shutting off the engine, likewise does the control board for the furnace.

A typical operation sequence for a furnace control board goes something like this:

  1. The control board receives a signal from the thermostat that the temperature is too low.
  2. It starts the ignition system, whether that be a spark generator, glow coil or pilot light.
  3. Once the ignitor is hot, the furnace control board initiates the flow of gas through the burners, where it is ignited.
  4. The control board keeps the furnace running until it is signaled by the thermostat that the temperature is now high enough, or until it detects something is wrong.

(An example of a malfunction where the control board would get involved is a thermocouple that is not detecting enough heat. In this case, the control board would shut off the gas flow to prevent a leak into the home.)

Furnace control boards are an essential part of your home’s HVAC system. And now, as a responsible homeowner, you know just how important. If suspect you have a problem with your furnace, give Boehmer Heating & Cooling a call!

Continue Reading

Finleyville Heating Installation Question: What is a Gas Furnace Draft Hood?

Friday, January 20th, 2012

As every Finleyville HVAC contractor knows, a draft hood is a necessary part of any gas burning appliance. For a gas furnace in particular it ensures steady air flow to the burners to avoid flares or the pilot light being put out by fluctuation in temperature and air flow.

What the Draft Hood Does

The draft will change in the chimney as exhaust vents towards it – especially when going from cold air to hot. A draft hood is placed above the upper most part of the gas furnace to draw air into the chimney and makes it possible to draw more or less air through the chimney as necessary to create a constant flow.

This makes it possible for the burner to enjoy consistent air flow without any wind gusts or sudden temperature spikes or drops. Hot air, if not put through a draft hood would create a strong air flow through the burners.

A draft hood cools the air as it is released by the burners from 500 degrees F to between 300 degrees F and 350 degrees F. The cooling needs to be carefully calibrated to avoid condensation build up in the chimney however – a problem that occurs when the temperature gets too low.

Maintaining Pressure

The draft hood is a part of a larger system designed to maintain air flow to the chimney. For every cubic foot of gas burned, the furnace needs to have 15 cubic feet of air for combustion and another 15 cubic feet of air for dilution. A draft hood and the rest of the ventilation system make it possible to put a furnace that has many thousands of BTUs in the basement of your home and still supply it with enough air to burn gas and dilute the exhaust before it enters the chimney.

For all of these reasons, if you see your pilot light flickering irregularly, notice a backflow of exhaust or a burning smell in your furnace room, it’s important to call a professional who can inspect and repair the problem before it becomes any worse. Not only can gas burner exhaust contain high levels of carbon monoxide, it can be bad for the device and the chimney if it doesn’t vent properly.

Continue Reading

A Question from Fox Chapel: What Does a Furnace Fan Limit Switch Do?

Monday, December 26th, 2011

When researching your Fox Chapel home’s furnace and potential problems it might have, you’ve probably run across a few references to the fan limit switch. And while you know that it can break in a number of ways, do you know what the switch does and what you should look for when checking your furnace its air handler for problems?

What the Limit Switch Does

To put it very simply, the furnace fan limit switch is a control that tells your furnace’s fan when to turn on and off. So, when the furnace isn’t on, it tells the blower not to operate (and send cold air into your home) and when the furnace is on, it tells the blower to turn on and start circulating the warm air.

While the primary function of the limit switch is to turn the blower fan on and off, it also has a safety role. When the temperature in the air supply plenum gets too hot, the limit switch turns off the furnace boiler to keep there from being any damage from overheating. This is handy if there is a blockage in the air vents or the controls are messed up due to water damage or improper adjustments to the settings.

Looking for Problems

Most of the time, when there is an issue with your furnace turning off or on frequently, the limit switch is one of the first things you will check. Because the switch is electronic and is attached to a thermostat which measures temperature in the air supply plenum, a small problem can result in it not working properly. So, you can easily check it by temporarily bypassing the switch and seeing if your device turns on or off properly.

In many cases, if the limit switch is the problem, you will still need to call a professional for replacement, but you can avoid a lot of headaches related to tracking down the source of the problem. If you suspect a limit switch problem, make sure to call someone immediately, because it does provide an important safety function and because without it your furnace won’t cycle on and off properly.

Continue Reading

West Mifflin Heating Tip: What to Check If Your Furnace Isn’t Lighting

Monday, December 12th, 2011

If your furnace isn’t lighting properly and your family is starting to suffer because of it, there are a number of possible problems you should check for before calling a West Mifflin heating contractor. Some of these issues can be fixed quickly by you while others may be signs of a serious problem that needs professional attention right away.

Checking the Pilot Light

If you have a gas furnace, the first step is to check the pilot light and ensure it is still working properly. If the pilot light is still on but goes out when you try to light the furnace or simply won’t stay on when you relight it, you may need to have the gas valve replaced. In some cases, it is as simple as the pilot light not being large enough and the gas blowing out the light.

This happens when gas enters the chamber and doesn’t ignite right away. When it does ignite, which happens after more gas enters the chamber, the extra force of the ignition will blow out the light. This is still a problem and should be inspected to ensure you don’t have any potential gas related issues.

Still Not Lighting

If you don’t have a pilot light or the unit still isn’t lighting, it may be an electrical issue. Electrical ignitions for gas furnaces should spark when the thermostat is turned on, so if it doesn’t you know that the switch or relay are bad.

If you smell gas or anything similar in the room where the furnace is located, you should immediately turn off the unit and call your gas company, followed by a technician. There could be a leak causing low pressure that results in your pilot light going out. Whatever the case, you need someone to look at it immediately.

Your furnace should always turn on when you flip the switch and if it does not, assume there is a problem. If you cannot find the problem yourself and easily fix it, you should call a professional. The risk inherent in an improperly working furnace (especially gas or oil) is too high to ignore.

Continue Reading

Mt Lebanon Heating Contractor’s Guide: Warning Signs of a Broken Furnace

Friday, December 2nd, 2011

How do you know when your Mt Lebanon home’s furnace is “on the fritz?” There are warning signs of a broken furnace and some are recognizable – but not all. A broken furnace not only deprives your home of heat and comfort, it also can be deadly, too.

Let’s look at some of the warning signs.

Each year, hundreds of people die and many more are injured from the most common household poison: carbon monoxide. This colorless and odorless poisonous gas comes from several sources and the furnace is the most common source of all; more precisely a broken or malfunctioning furnace. Carbon monoxide is a result of incomplete combustion of a fossil fuel, which is when a fuel does not burn correctly or completely. In a furnace, carbon monoxide gas comes from a poorly operating burner or a cracked heat exchanger. A properly tuned and maintained furnace greatly reduces the risk of carbon monoxide poisoning.

Since carbon monoxide gas is colorless and odorless, it can go undetected. It can make people sleepy and create flu-like symptoms. Sometimes a person may fall asleep and never wake up. But there are warning signs. Drowsiness, vomiting, or flu-like symptoms are a warning sign. Regularly scheduled maintenance of your furnace by a qualified heating and cooling professional and installation of carbon monoxide detectors can reduce the risk of falling ill to carbon monoxide gas.

Another warning sign is a higher energy bill. Sometimes you can’t detect a problem right away because, like carbon monoxide, there may be no obvious signs. Higher utility bills can be a sure sign of a furnace that is working too hard and running more than usual. This may be a result of clogged or dirty air vents, or dirty filters. If your monthly bills are higher than those of the previous year, it may not just be because gas prices are higher.

There are other warning signs of a broken furnace, too. The most obvious is the failure of your furnace to bring your home up to the desired thermostat settings or to maintain an even temperature. Cold or uncomfortable houses are sure signs of a broken furnace. The furnace may cycle on or off, causing an uneven or inconsistent flow of heated air. This can be because of a poor blower or a clogged furnace filter. If you don’t feel any moving heated air or detect any unusual odors or smells coming from your heating vents, that’s a sure sign of a broken or malfunctioning furnace.

A broken or cracked gas line can emit odors and can cause a furnace to malfunction, too.

Don’t take a chance of losing heat and comfort this winter. At the first possible warning sign, call your Mt Lebanon heating professional for a heating system tune-up.

Continue Reading

What to do if Your Heating System Breaks: A Guide from Bridgeville

Monday, November 14th, 2011

What if the heart of your Bridgeville home’s heating system – the furnace – stops working? The warm air that used to flow from your vents has been replaced by a chilly draft. It isn’t time to panic, but it is time to take action. Before you do anything, determine why the furnace stopped working. It may be something as simple as a tripped circuit breaker in your electrical panel. Check the circuit breakers first.

The pilot light in your furnace may have blown out. It can be re-lit if you follow the directions in your furnace owner’s manual. You can find answers on how to re-light a pilot light on the Internet, too.

If the shutdown has not been caused by an electrical or pilot light failure, there is still no need to panic. But another obvious question is: did you pay your last gas bill? Maybe you had a shutoff notice and either ignored it or forgot about it.

Now that you are convinced that the furnace has stopped working, here are some things you should do. First, find the name of a qualified heating and cooling professional. If you already use a heating contractor, contact them and schedule a service call.

While you are waiting for help to arrive, ensure that everyone is safe and accounted for. Make sure pets are nearby and protected from the cold, too. What you don’t want to do is use any appliance to keep you warm that is not designed to keep you warm, like a stove. If you have electric space heaters or propane heaters, carefully locate them in a well vented room (windows open a bit or portable fans circulating air). You don’t want any build-up of gases from fossil burning appliances, gases which could contain deadly carbon monoxide.

Huddle up everyone into a room and break out lots of blankets. You may even want to make an “adventure” of this – find a movie to watch and pop up a bunch of popcorn.  If your waiting time is more than 24 hours, you might want to call up a friend or relative and make arrangements to spend the night with them.

The main thing to remember is not to panic. Most qualified heating contractors, knowing the circumstances, will send out a repair person in a matter of minutes or within one or two hours. Just remember to avoid keeping warm by using unvented heating devices.

Continue Reading

Furnace Fan Doesn’t Run? Why Is That? What Should You Do? A Guide from Bridgeville

Wednesday, November 2nd, 2011

There are several reasons that a furnace fan might stop working at one point or another. While many of these do require a Bridgeville professional‘s attention, there are probably some things you can check on your own before you go and call in the pros. After all, if you can address the problem on your own, it will at least save you from having to pay a technician to come out.

The first thing to check when your furnace is running but the fan isn’t turning is whether or not the fan is actually switched on. Certain models of furnaces have a separate switch to turn the fan on and off. While there is probably no reason that you would want to turn off the fan by itself, it’s worth taking a look just in case. If that really is the problem, you’ll be up and running and back to dealing with better things in no time.

If that’s not the problem, you might try looking to see if any wires leading to the fan are loose or the fuse is blown. If the fan has no power, of course, it won’t be able to work but the rest of the furnace likely would work just fine as long as it doesn’t run on electricity as well.

Of course, the problem very well may be beyond your power to solve on your own. Don’t despair though. Even though you need to call in a professional, that doesn’t mean that the problem will be expensive to fix. In fact, it may be as simple as replacing your thermostat or the motor for the fan itself.

Just because a fan isn’t working doesn’t mean that you’re going to be paying an arm and a leg to have work done on your furnace. If you can’t easily discover the problem on your own, however, or if you’re not comfortable inspecting this type of equipment at all, you’re generally better off just calling in an expert and letting them do the dirty work for you. Paying for simple furnace fan repairs is definitely preferable to having to pay someone to fix the fan and the stuff you broke yourself while trying to fix the fan on your own.

Continue Reading

Is Your Furnace Making too Much Noise? (and Happy Halloween Weekend!)

Friday, October 28th, 2011

Happy Halloween weekend from everyone at Boehmer Heating & Cooling! We hope you have a fantastically spooky time! But don’t be scared of the noises coming from your furnace, here is some information about common causes and solutions.

The old saying that “It is better to be seen than heard” certainly applies to the mechanical equipment in your Pittsburgh home. If you hear a squeaky noise or loud clattering you automatically suspect that something is wrong. And if that noise is coming from your furnace, you better pay attention to it. A noise is an obvious sign of a problem – minor or major – and it could result in mechanical failure that could leave your home cold and uncomfortable – and affect your home’s indoor air quality.

Today’s newer variable-speed furnaces keep a constant airflow through the ventilation system utilizing a low speed fan that consumes small amounts of electricity. Constant airflow brings in fresh air and keeps the room air from becoming stale or stagnant. Because of this constant operation, it is important to ensure the furnace is running at peak efficiency, which also means that it is running quietly.

Here are some common noises, possible reasons, and suggested repairs. As always, if you are in doubt about how to repair your furnace, call a local qualified heating contractor and schedule a service call.

  • Squealing noise – could be a worn out or slipping blower belt. Check for proper tension of the belt or replace the belt if it is worn out or cracked.
  • Squealing noise – could be worn out motor shaft bearings. Lubricate the blower motor at the proper points.
  • Rumbling noise – often caused by a poorly adjusted pilot light when the burners are turned off. Adjust the pilot as necessary.
  • Rumbling noise – often caused by dirty gas burners when the burners are switched on. This problem requires service from a qualified heating technician.
  • Buzzing noise – often caused when a blower motor mounting come loose. Tighten the mounting screws or use shims to fill gaps.
  • Hissing noise – indicates a possible air leak. This problem requires service from a qualified heating technician.
  • Ticking noise – possibly a leaky gas valve. This problem requires service from a qualified heating technician.
  • Rattling noise – could be a dirty fan blade. Wipe the fan blade or clean with degreaser.
  • Rattling, grinding, or whining – could be resistance to airflow that causes the motor to work harder. Check the vents in each room for dirt, debris, or obstructions and clear them.
  • Vibrating noise – may not be the furnace but loose or cracked seams in the ventilation system. Check the ductwork seams and hangers to ensure everything is tight. You may need duct tape or bracket hardware.

The best way to keep your furnace and ventilation system from making noises is to practice preventative maintenance. Have your furnace checked annually by a qualified heating contractor – and enjoy the peace and quiet.

Continue Reading