Boehmer Heating & Cooling Blog : Archive for February, 2012

Pittsburgh Heating Replacement Tip: Replace vs Repair

Friday, February 3rd, 2012

We all dread an expensive repair in Pittsburgh, whether it is a car that needs a new transmission, a leaky roof that needs new shingles, or electrical wiring that has been chewed up by a wild animal. We often try and put bandages on things that we know should be replaced but we just can’t afford to replace them.

The same can be said about your home’s heating system. When your heat goes out or your home just doesn’t seem to be heating up to the setting on your thermostat, your first inclination is to check and see if it is running. Some people will put their hand over a heating vent to check for hot air while others may go into the basement or mechanical room to listen to hear if the furnace is running. Maybe there is a blockage in the ventilation system or a blown circuit breaker, two relatively easy fixes.

If the furnace isn’t working after checking the obvious symptoms, your next move is to call for service. Any qualified heating professional would be able to diagnose your problem and offer suggested repairs. Something relatively minor like a bad circuit board or blown fan motor are not real expensive repairs and are the best option versus replacing the furnace. And you may keep experiencing the same problem and getting the same repair work done – anything to avoid an expensive replacement.

But at some point the vicious cycle will come to an end. Your repair bills will begin to inch their way past the cost of replacing the furnace. You can only bandage a problem so long before it becomes “unfixable.” You may not want to pay an expensive replacement bill but consider the alternatives.

First is the obvious – it costs too much to keep repairing the furnace. Secondly, you never know when the furnace may break down and its failure to operate could have dangerous effects on the people in your home, especially if someone is sick. Third, your furnace may not be able to keep up with the heating demand due to lifestyle changes, i.e. an addition put on the house, carpeting removed and wood floors exposed, a new window, door, or skylight added, etc. Your old furnace may not have been designed to keep up with these changes and the repairs are only delaying the inevitable.

Ask yourself if everyone in your Pittsburgh home is comfortable during cold weather. If most answer no, it may be time to consider replacing that old furnace with a new, energy efficient model that uses today’s technology – and leaves a smaller carbon footprint – to keep up with the demand for heat, in any sized building or home. Your decision to replace your old heating system could be as simple as the need to use modern technology to solve your indoor comfort problems.

Continue Reading

O’Hara Heating Repair Question: What Causes Cracks in a Heat Exchanger?

Wednesday, February 1st, 2012

Furnaces are designed so that the heat – and the combustion byproduct produced inside – doesn’t interact directly with the outside air. This design is to ensure you have a safer furnace in your O’Hara home that won’t inadvertently affect your family’s health.

The metal piece that separates the furnace heat from the outside air stream is called the heat exchanger. The heat exchanger performs a very important function, and if it is broken or cracked, it can’t work properly.

A cracked heat exchanger is very common problem with heating systems, as well as one that should be repaired as soon as possible. But what causes a heat exchanger to crack? Here are some of the most common reasons:

  • A long period of normal use. A furnace heat exchanger naturally expands and contracts with the heat of the furnace, over and over again as the furnace is turned off and on to heat the home. Over several years, this stress can crack the metal.
  • Poor air flow, often caused by dirty or obstructed vents, can result in poor air flow through the furnace. This overworks the furnace, which can crack the heat exchanger prematurely.
  • Poor, incomplete or improper combustion can also cause a heat exchanger to crack. When the combustion process is less efficient – which can also be a result of poor air flow — your furnace’s burners have to run hotter and longer to heat your home, which means extra stress on the heat exchanger.

Essentially, if a furnace is running at less than optimal efficiency for an extended period of time, the heat exchanger is put under additional stress beyond the usual and can crack prematurely. Therefore, the best way to prevent a cracked heat exchanger is proper maintenance, particularly keeping all vents clean and unobstructed and getting an annual maintenance inspection.

If your heat exchanger does crack, do not hesitate to call an O’Hara professional and get it repaired. The crack can allow potentially dangerous combustion gases to seep into your home, which can have a negative impact on your family’s health.

Continue Reading