Boehmer Heating & Cooling Blog: Archive for December, 2011

How to Make Your Heating System More Effective in South Hills

Friday, December 9th, 2011

Everyone in South Hills wants an effective heating system – one that will provide steady, reliable heat without you having to spend hundreds of dollars each month on gas, oil or electricity. And while the best way to improve the efficiency of your heating system in most cases is to upgrade it, there are some simple things you can do around the house to boost its effectiveness. Here are some of the best:

  • Rearrange Furniture – Just having the heat on doesn’t necessarily ensure the heat entering your room is being distributed evenly. Move your furniture in such a way that there is a clear, unimpeded path from the registers and radiators to the rest of the room. Done properly, this will make it much easier to and faster to heat every room of your house.
  • Maximize Air Flow – Air flow can be maximized in a number of ways. Make sure you close any windows near a register or radiator and that you remove any large objects that might block air flow. You should also install things that can help move air like fans and always call someone in for changes to the arrangement of your vents or radiators.
  • Clean Registers or Radiators – The cleaner your radiators or dust registers are, the more efficiently they release their heat. Not only have that, but clean radiators and registers resulted in better indoor air quality. Weekly cleaning of each room’s heating source is highly recommended.
  • Install Ceiling Fans – Ceiling fans switched to blow down are incredibly effective for distributing air throughout the room. This will keep push warm air down and keeps cold air up – in effect, reducing the need for constant running of your furnace or boiler.

Effective heating is important to keep your home comfortable, reduce the cost of heating and prolong the lifespan of your furnace or boiler. You should also make sure your heating system is properly maintained throughout the year. Skipping maintenance visits (which are highly recommended annually) will put unnecessary stress on your system and shorten its lifespan substantially, not to mention the decrease in efficiency when heating your home.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on How to Make Your Heating System More Effective in South Hills

A Tip from Verona: Where to Place a Thermostat for Accurate Heating

Wednesday, December 7th, 2011

It’s easy to forget with your furnace in the basement churning away all day to keep your Verona home warm, but your thermostat is the single most important device in ensuring your home is heated to the temperature you want. If it stops working or it misreads the temperature inside your home, your furnace won’t know what temperature it actually is and will turn on and off at the wrong time.

Where Not to Place Your Thermostat

To avoid inaccurate readings, avoid placing your thermostat in the following locations:

  • Direct Sunlight – Direct sunlight will almost always increase the perceived temperature of the thermostat. Unless you live in a greenhouse, this will be very uncomfortable for everyone in your home.
  • Windows – Windows can result in direct sunlight and breezes. If the windows are not properly sealed, cold air can blow in and make it seem cooler in your home than it really is. In any of these cases, your thermostat will misread the indoor temperature.
  • Drafts – Drafts from improperly sealed doors, windows, or anything else in your home can negatively impact the thermostat.
  • Heat Vents – Don’t place your thermostat near a radiator or heat vent where it is likely to be warmer than anywhere else in the house.
  • Kitchens – Kitchens tend to be warmer than other rooms in the house, especially when in use. Avoid placing a thermostat here unless you have a zone control system and your kitchen is separate from other rooms.

A properly placed thermostat will ensure your home is heated or cooled to the temperature you desire regardless of outdoor conditions. If you’re unsure whether your thermostat is calibrated properly, check the temperature with a separate thermometer in a different location in the same room. If it is significantly warmer or cooler in one place than another, try to determine which is more indicative of the actual comfort level in your home. When properly located, your thermostat should never be an issue again.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on A Tip from Verona: Where to Place a Thermostat for Accurate Heating

A Question from Allison Park-Hampton: How Do I Check a Gas Furnace Draft Pressure Switch?

Monday, December 5th, 2011

There are many reasons why a furnace stops working and in many cases, an Allison Park-Hampton homeowner can perform some simple diagnostics to pinpoint the problem. Finding the problem is one thing – fixing it is another. When in doubt, don’t try it yourself. Call a qualified heating contractor.

But let’s look at one possible problem and solution you may be able to perform yourself – testing the draft pressure switch. The draft pressure switch on a gas furnace allows an electrical current to pass through to ignite the furnace. The pressure switch monitors the draft conditions and won’t allow the furnace’s gas valve to open unless draft is correct.

If the switch is malfunctioning, so too will (or will not) the furnace.

The best way to locate the switch is by consulting with your owner’s manual or by going online and simply typing in the words “gas furnace draft switch.” It is identifiable by its round size and is bolted to the outside of the furnace. It should be nearby the draft inducer motor because the two are connected by a metal tube. The tube may sometimes be the culprit, too. A tube that is blocked with condensation may cause the switch to go bad.

To check for proper function, first turn off power to the furnace, either by shutting down the ‘on’ switch at the furnace or shutting off the circuit breaker.

Use a volt ohm meter to check if the switch is opening and closing properly. Start by zeroing out the meter’s probes by touching the tips together. Using the dial (could be analog or digital), set the meter to 24 volts. Ground the black probe by attaching it to any metal part of the furnace. Then place the end of the red probe on the metal tube connecting the draft pressure switch to the draft inducer motor.

If the switch is working properly the meter should read at least 24 volts, or very near that. If the reading is short of 24 volts, the switch is not working correctly. At that point you may decide to replace it or call a professional to do the task (recommended).

Always remember that there are many sources which will help you diagnose and repair a problem, especially those available through the Internet. If you search YouTube.com you will find many videos advising you on how to repair certain components. Use all of the resources available to you and keep the phone number of a qualified and professional heating and cooling contractor nearby.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on A Question from Allison Park-Hampton: How Do I Check a Gas Furnace Draft Pressure Switch?

Mt Lebanon Heating Contractor’s Guide: Warning Signs of a Broken Furnace

Friday, December 2nd, 2011

How do you know when your Mt Lebanon home’s furnace is “on the fritz?” There are warning signs of a broken furnace and some are recognizable – but not all. A broken furnace not only deprives your home of heat and comfort, it also can be deadly, too.

Let’s look at some of the warning signs.

Each year, hundreds of people die and many more are injured from the most common household poison: carbon monoxide. This colorless and odorless poisonous gas comes from several sources and the furnace is the most common source of all; more precisely a broken or malfunctioning furnace. Carbon monoxide is a result of incomplete combustion of a fossil fuel, which is when a fuel does not burn correctly or completely. In a furnace, carbon monoxide gas comes from a poorly operating burner or a cracked heat exchanger. A properly tuned and maintained furnace greatly reduces the risk of carbon monoxide poisoning.

Since carbon monoxide gas is colorless and odorless, it can go undetected. It can make people sleepy and create flu-like symptoms. Sometimes a person may fall asleep and never wake up. But there are warning signs. Drowsiness, vomiting, or flu-like symptoms are a warning sign. Regularly scheduled maintenance of your furnace by a qualified heating and cooling professional and installation of carbon monoxide detectors can reduce the risk of falling ill to carbon monoxide gas.

Another warning sign is a higher energy bill. Sometimes you can’t detect a problem right away because, like carbon monoxide, there may be no obvious signs. Higher utility bills can be a sure sign of a furnace that is working too hard and running more than usual. This may be a result of clogged or dirty air vents, or dirty filters. If your monthly bills are higher than those of the previous year, it may not just be because gas prices are higher.

There are other warning signs of a broken furnace, too. The most obvious is the failure of your furnace to bring your home up to the desired thermostat settings or to maintain an even temperature. Cold or uncomfortable houses are sure signs of a broken furnace. The furnace may cycle on or off, causing an uneven or inconsistent flow of heated air. This can be because of a poor blower or a clogged furnace filter. If you don’t feel any moving heated air or detect any unusual odors or smells coming from your heating vents, that’s a sure sign of a broken or malfunctioning furnace.

A broken or cracked gas line can emit odors and can cause a furnace to malfunction, too.

Don’t take a chance of losing heat and comfort this winter. At the first possible warning sign, call your Mt Lebanon heating professional for a heating system tune-up.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on Mt Lebanon Heating Contractor’s Guide: Warning Signs of a Broken Furnace